The Cost of a Trip between Burlington City, New Jersey and Washington Township, New Jersey
Traveling between Burlington City and Washington Township in New Jersey is a journey that takes you through some of the state's most beautiful landscapes, interesting towns, and impressive highways. But how much does it cost to travel between these two places, and what are your options for getting there? Let's take a closer look.
Routes and Distances
There are three popular routes you can take to travel between Burlington City and Washington Township, and the distance and cost of each vary significantly. Let's explore each option in more detail:
Route 1: NJ-90 W and NJ-45 S
This is the shortest and most straightforward route, covering a distance of just over 20 miles and taking around 30 minutes when traffic is good. To get to route 1, you start at the intersection of High Street and Burlington-Bristol Bridge in Burlington City.
The primary advantage of this route is its simplicity. You only have to take a few roads, and there are no major traffic lights or intersections along the way. The downside is that it's a tolled road, with a fee of $1 to cross the Commodore Barry Bridge. You will also need to contend with rush hour traffic during peak times.
Route 2: NJ-295 S and NJ-42 S
This route is more scenic and takes you on a longer, meandering journey through some of New Jersey's hidden gems. To get here, you start at High Street and Route 130 in Burlington City.
The journey covers around 28 miles and takes an average of 50 minutes. It's a popular choice for those who want to take in some of South Jersey's picturesque countryside, as it passes through small, charming towns such as Mount Laurel and Haddonfield.
The downside of route 2 is that it is by far the longest of the three, and it also has more potential traffic and stoplights, both of which can slow you down. While the scenery is a significant bonus, it might not be worth the extra time invested, depending on your plans.
Route 3: NJ-73 S and NJ-42 S
This is a good middle ground between routes 1 and 2, covering 25 miles and taking about 40 minutes in moderate traffic. To take this route, you start at the intersection of Route 130 and Florence-Columbus Road in Burlington City.
The journey is scenic but not as much so as route 2. It also takes you through some small towns and residential areas, but the roads are mostly well-maintained and free of traffic. The main drawback is that it's not as direct as route 1, and there are several traffic signals to contend with.
Costs
The costs of traveling between Burlington City and Washington Township depend on which route you choose, what mode of transportation you use, and whether you need to account for tolls, parking, or any other incidental expenses. Let's explore each option in more detail:
Driving
If you opt for driving, you will need to factor in the cost of gas, which varies depending on the fuel efficiency of your car, the gas station you use, and current gas prices. Suppose you have a typical family-sized sedan with a 15-gallon tank, and you average around 30 miles per gallon (the national average). In that case, you can expect to spend between $20 to $30 on gas alone, depending on the route and current prices.
You will also need to take into account any tolls you incur, such as the $1 toll to cross the Commodore Barry Bridge on route 1 and any additional parking fees you might need to pay to access your destination. Finally, you'll need to factor in the cost of wear and tear on your car, such as oil changes and tire rotations, which can add up over time.
Public Transportation
Another option you could consider is taking public transportation, such as a train or a bus. This is typically the most economical option, as it eliminates the need for gas and tolls, and you don't need to account for wear and tear on your vehicle.
The cheapest and most convenient public transportation option for this route is to take the RiverLine Rail between Burlington City and Camden, connect to PATCO, and then get on the bus from there. The entire journey would cost just $6.60, and it would take around two hours. However, you would need to factor in the time it takes to walk or drive to the nearest train or bus station, which could add a considerable time cost to your journey.
Recommendation
Based on the above information, if you're looking for the quickest and most direct route to travel between Burlington City and Washington Township, we'd recommend route 1, NJ-90 W and NJ-45 S. While it is a tolled road, there are no significant traffic lights or major junctions, and it takes less than 30 minutes to complete the journey under optimal conditions.
If you have more time or if you're looking to take a scenic route, then consider route 2, NJ-295 S and NJ-42 S. It's a longer drive, but it takes you through charming towns and exposes you too picturesque landscapes that make for a great trip.
Finally, if you're looking for an economical route and don't mind taking public transportation, then the RiverLine Rail between Burlington City and Camden and then connecting with PATCO and Route 404 is your best option. It takes the most time, but it's also significantly cheaper.
Conclusion
In summary, there are several ways to travel between Burlington City and Washington Township, each with its advantages and disadvantages. The best route for you depends on your preferences, your budget, and your time constraints, so be sure to evaluate your options carefully before setting out on your journey. However, if you're looking for a direct, quick, and straightforward way to get between these two places, then we'd recommend NJ-90 W and NJ-45 S every time. However, if you have more time and want to take in the best of New Jersey's countryside and charming towns, you could consider route 2. Whichever option you take, we hope you enjoy your trip!